W. H Rea Engineering.
W. H Rea Engineering.

Sheep Trailers 

Sheep Dipping Trailers

 

250 Gallon Sheep Dipping Trailer.

 

Length (platform):                6.50 mtr

Width (overall width):          2.40 mtr

Height (Floor):                        1.10 mtr

Height: (overall)                     2.13 mtr

Tub Capacity:                           250 Gallon

 

250 Gallon Sheep Dipping Trailer.

 

  • Front view
  • longer lower angled entrance ramp
  • Alloy floor with rasied steps for good grip when on the ramp 

Sheep walk up the 3.35mtr long ramp and straight unto side entry floor section and then slide through the tarpaulin and into the tank. 
Out of the tank and unto the 2.4mtr x 2.2mtr dripping area before being let out through the guillotine gate and down the 2.7mtr exit ramp.
Unit is supplied with some railed hurdles to help with penning requirements.

 

 

 

250 Gallon Sheep Dipping Trailer.

 

 

 

 

 

  • Rear exit through guillotine gate
  • Ramps for good grip for safe entrance and exit control
  • Large 250 Gallon Side entry dipping tank c/w release bung
  • Work gantry at side and front of tank.
  • Decoy pen at back of entrance ramp.
  • Twin axle unit c/w stabilising /levelling jack legs on each corner and at front of tank.

 

250 Gallon Sheep Dipping Trailer.

 

 

  • Side entry straight through tank in centre  & decoy pen to the right
  • Alloy tread plate flooring on deck level and also ramps

 

 

 

 

  • This design of contractors unit is time proven with many years of success through direct hire from yard.

Sheep Handling Trailers.

15Ft Long x 6Ft 6" Wide Sheep Handling Trailer.

 

Fully Galvanised Trailer which is completely stabilised for no nonsense off ground working.

Twin foot baths sections - one for the narrow race for walk through solutions containing a4Ft clean water bath a plus a 8Ft solution bath. The other footbath is a large 12ft x 3Ft wide bath for stand-in solutions. 

All with anti slip expanded metal

Foot baths are built into an under the floor sections and covered with removable alloy tread panels to allow full use of normal floor

 

15Ft Long x 6Ft " Wide Sheep Handling Trailer layout

 

10Ft Long x 3Ft Wide Sheep Handling Trailer.

 

Extends from 10Ft to 20Ft long wroking race by use of pull out hurdles and end gates.

 

The race can handle small or big flocks with the greatest of ease. Set up time for race and penning is 10 mins, race extension plus penning fit inside race when transporting.

10Ft Long x 3Ft Wide Sheep Handling Trailer.

 

 

Shearing Trailers.

We design and maunfacture  high quality Sheep Shearing Trailers to client requiremnts. We make  one man.two man three man and four man operator units. 

Single Axle One Person Operation Trailer 

One Man Operator Shearing Trailer.

 

11Ft Long unit

  • The unit is buil ton a custom made chassis. 
  • A shearing race section is built onto one side including one sprung loaded drafting panel to draw out onto the shearing area.
  • The outer side drops down to be included as a work platform.

 

 

One Man Operator Shearing Trailer.

 

  • At the front of the race, a head locking catch gate holds the decoy ewe.

 

 

One Man Operator Shearing Trailer.

 

 

  • Main shearing area is on a heavy timber board floor. With the race areas on expanded metal flooring.
  • Heavy jacks for levelling and steadying at each corner.
  • Trailers are mostly custom built to the specific requirement of the client.

Twin Axle Two Person Operation Trailer 

Two Man Operator Shearing Trailer.

14Ft long unit

  • The unit is built on a new modified Ifor Williams 14Ft x 6Ft 6" Flat Bed Trailer . 
  • Easily transformed in a matter of minutes back to flat bed trailer of duel use. 
  • A shearing race section is built onto one side including two sprung loaded drafting panels to draw out onto the shearing area.
  • The outer side drops down to be included as a work platform.

 

Two Man Operator Shearing Trailer.

 

 

 

At the front of the race, a head locking catch gate holds the decoy ewe.

 

Two Man Operator Shearing Trailer.

Main shearing area is on a heavy timber board floor with run off exist ramps. 

  • With the race areas on expanded metal flooring.
  • Heavy jacks for levelling and steadying at each corner.
  • Trailers are mostly custom built to the specific requirement of the client.

Three/Four Man Operator Shearing Trailer.

16Ft Long Unit

These trailers are similar to the Two Man Operator Trailer but the race runs up the centre of the trialer with two tripper doors to the left hand side and two doors to the right hand side..

Both sides fold down to become part of the work platform.

Scanning Trailer. 

10Ft x 6Ft

 

Self contained sheep scanning trailer.
Custom built 10Ft x 6Ft trailer (plated fully road legal)
Easily and quickly converted back into a flat bed trailer for multi use.
Heavy duty tarpaulin cover with fully customised advertising graffics which aids protection from the elements and essential for good visibility of the scanner screen.

 

 

The operator sits inside the enclosed part of the trailer with all his equipment, from where, in addition to actually scanning the ewes, he can easily mark them and operate the exit gate. The operator can keep a tally of the number of barrens, singles, twins etc, and can also spot early signs of potential problems such as Toxoplasmosis.

 

Reaching out from his work area, the technician holds the transducer on the belly of the ewe while interpreting the resultant image on a screen.

The width of the race in which the ewe is standing is adjustable for different breeds or sizes of sheep, so, whatever the type, they’re always presented in the right position and are unable to jump about too much.

 

 

Plenty of space on board to carry additional essential hurdling and pens.

 

The whole unit only takes a matter of minutes to set up and get ready to scan.

Contact details

W. H Rea Engineering.

290 Lisnevenagh Road,

Antrim

BT41 2JL

 

Tel: 02894 462 193 02894 462 193

 

Alternatively, please use our contact form. Contact Us

Tweets from WH Rea Engineering @WHReaEng

News

A big thank you to the guys at Rea Engineering for a wonderful job.

We got in a dispute with the developer who never finished the development to spec, all the residents got together to agree on fitting new gates and railings.   W. H Rea Engineering.were pivotal in gaining agreement on the gate designs plus the induvidual automation requirements, and costs.

Thank you for making a complex issue... simple.

Eoin
Local Resident                 

 

Hi Gilbert, 
            Many thanks for the fantastic gates – they completely change the look of our house.
The detail  and design of the gates really complements the house and garden.

Regards

Stephen
Rhanbuoy Park

Tender accepted

Successful ideas:

The contract for a major project on Dublin Road , Belfast has been awarded to W. H Rea Engineering., by May Estates Ltd .

More news to follow........

Print Print | Sitemap
©2017 W. H Rea Engineering.